How a hand-wound watch keeps time
A spring stores the power; a train of wheels spends it. But a spring on its own would empty itself in seconds. What makes a watch a watch is the part that lets the power out in small, equal steps: the escapement, paced by the balance.
This is the WB-1, seen from the back with its bridges on, running at its true beat rate, five beats a second. Every picture on this page is live. Drag to turn it; use the sliders and buttons to drive it. You can at any time.
The escapement
Two parts do the work. The escape wheel is the last wheel of the train; the mainspring is always trying to turn it. Its teeth are not like gear teeth: each one ends in a small club. Opposite it sits the pallet fork, a lever on its own staff, carrying two pallet stones of synthetic ruby. Ruby is hard and slippery against steel, so the stones barely wear in a lifetime of sliding.
Put them together and the fork becomes a gate. With the fork against one side, a tooth lands on a stone and the wheel stops dead: it is locked. Move the fork across and that stone lifts out of the way; the wheel turns a little, until a tooth lands on the other stone. Try it:
Each swing of the fork lets the wheel move half a tooth, and no further. Fifteen teeth, two swings a tooth: the escape wheel needs thirty swings of the fork to go once round. Pace the swings and you have paced the whole train.
The balance
Something has to swing the fork at a steady rate. Watches use a wheel on a spring. Twist it and let go: the spring pulls it back, it overshoots, the spring pulls it back again. The time for one full swing depends on just two things, how stiff the spring is and how heavy the wheel is, and how far out its weight sits:
Stiffer spring, faster swing. More weight at the rim, slower swing. And, the important part, the period hardly changes as the swings die away. That is why a balance makes a good clock. In a watch the wheel is the balance and the spring is the hairspring, a coil finer than a hair. This movement's balance swings two and a half times a second: five beats a second, 18,000 an hour.
Under the balance, on its staff, sits a small table carrying one more ruby, the impulse jewel. Twice a swing it passes through the notch at the end of the fork. Slow it right down and step through one pass:
Read the steps left to right. Unlock: the jewel kicks the fork, and the stone slides off the tooth that was resting on it. Impulse: the wheel, freed, pushes on the slanted face of the stone, and the fork hands that push back to the balance through the jewel: a nudge, like pushing a child on a swing, that makes up for what friction took. Drop: the tooth leaves the stone and the wheel jumps forward a fraction. Lock: the next tooth lands on the other stone, and the fork is pulled tight against its stop. Then the balance swings on, free and untouched, for most of its arc. That freedom is the whole design: the balance is touched for only a few degrees of each swing, so the spring, not the train, sets the time.
The mainspring
The power comes from a strip of hardened spring steel coiled up inside a drum, the . The inner end of the mainspring hooks onto the barrel arbor, the axle through the middle; the outer end hooks onto the inside of the barrel wall. Winding turns the arbor and pulls the coils in tight around it. Left alone, the spring tries to uncoil, and since the arbor is held, the only thing it can turn is the barrel, which has teeth round its edge.
Wind it up with the slider and watch the coils move from the wall to the arbor. Then let it run: the arbor stays put and the barrel turns instead, slowly letting the coils back out to the wall. What stops the arbor slipping back while you wind is the ratchet wheel on top of it and the click, a sprung pawl that rides up each tooth and drops behind it. It lets the arbor turn one way only. That clicking is what you hear and feel at the crown.
A full wind here is six turns of the arbor, and running down gives those six turns back through the barrel. In this movement each turn of the barrel takes eight hours, so on paper a full wind lasts 48 hours. In practice the last stretch of a let-down spring is too weak to keep good time, so the useful reserve is shorter than the paper figure.
The going train
The barrel turns far too slowly to show the time on its own, and far too strongly to feed the escapement directly. A chain of wheels sits between them, the going train. Each large wheel drives a small pinion on the next arbor. A wheel of 80 teeth driving a pinion of 10 makes the pinion turn eight times as fast, with an eighth of the force. Four such steps take the barrel's eight-hour turn down to the escape wheel's six seconds:
| Arbor | Driven by | Teeth | One turn takes | Turns |
|---|---|---|---|---|
| the mainspring | 80 | 8 hours | 0 | |
| Centre wheel | pinion of 10 | 80 | 1 hour | 0 |
| Third wheel | pinion of 10 | 75 | 7½ minutes | 0 |
| Fourth wheel | pinion of 10 | 80 | 1 minute | 0 |
| Escape wheel | pinion of 8 | 15 | 6 seconds | 0 |
Two of those arbors are put to work directly. The centre wheel turns once an hour, so it carries the minute hand. The fourth wheel turns once a minute, so it carries the seconds hand. At the true beat rate you can see the train jump: the escape wheel moves in five small steps a second, and every wheel behind it steps with it, right back to the barrel. Speed it up and the steps blur into a smooth turn.
The close-ups show how the teeth are cut. A watch wheel's teeth are curved only above the pitch circle, in a shape called an epicycloid, and the pinion leaves have straight flanks with a rounded top. Cut that way, a wheel and pinion pass the turning force along at a perfectly steady ratio, with the working faces rolling against each other rather than scraping. There is always a little free play, the shake, so the train can never jam on a speck of dirt or a drop of oil.
Check the arithmetic against the balance. The escape wheel lets one tooth through for every two swings of the fork, so its 15 teeth take 30 beats. At five beats a second that is six seconds a turn, which is exactly what the train gives it.
The motion work
The train gives us minutes and seconds, but nothing in it turns once in twelve hours. That job belongs to a small set of wheels under the dial, the motion work. The cannon pinion is a tube that sits on the centre arbor and carries the minute hand. It drives the minute wheel, three times slower, and the minute wheel's own pinion drives the hour wheel, four times slower again. Three times four is twelve: the hour wheel, riding on a pipe around the cannon pinion, carries the hour hand round once while the minute hand goes round twelve times.
One more detail makes setting the hands possible. The cannon pinion is not fixed to the centre arbor: it is held on by friction, tight enough to be carried round by the train, loose enough to slip when you turn the hands by the crown. Too loose and the hands lag or stop while the watch runs; too tight and setting the time strains the train. Checking that grip is one of the jobs on the bench.
The keyless works
One stem and one crown do two jobs: wind the spring and set the hands. The parts that switch between them are called the keyless works. The stem has a square section, and on that square slides the clutch, so it always turns with the crown. Push the crown in and the clutch is pressed against the winding pinion, which turns freely on the round part of the stem. Pull the crown out and the clutch is moved the other way, onto the setting wheel.
Wind with the crown pushed in. The winding pinion turns the crown wheel, which turns the ratchet wheel on the barrel arbor, and the click holds every bit gained. Now drag the slider back: the teeth between clutch and winding pinion are cut like a ratchet, sloped on one side, so turning the crown backwards just pushes the clutch away and lets it click over them. That is the soft clicking you feel winding a watch the wrong way.
Pull the crown out and watch the levers. A pin on the setting lever sits in a groove on the stem, so the lever follows the stem out. It swings the yoke, whose fork sits in a groove round the clutch, and the yoke slides the clutch off the winding pinion and onto the setting wheel. Turn the crown now and the setting wheel drives the minute wheel and the cannon pinion: the hands move, and the cannon pinion slips on its arbor exactly as described above.
On the bench: the timegrapher
Everything above can be heard. Put a movement on a timegrapher and a microphone in the stand picks up every beat. The machine compares each beat with a quartz clock and prints a dot: a beat that comes late sits a little higher than the last, a beat that comes early a little lower. A watch that keeps perfect time draws a flat line. One that gains draws a line that climbs; one that loses, a line that falls.
Read the trace from the top. Two rows of dots instead of one means beat error: the tic and the toc are not evenly spaced, because the balance does not come to rest with the jewel centred in the fork. The slope is the rate, set by the regulator, which changes how much of the hairspring is free to work. The lower picture is the sound of one beat. Its first burst is the unlock and its last is the drop, the same steps you watched in the slowed-down escapement. The time between them depends on how fast the balance is moving as it passes the fork, and from that, with the lift angle of the escapement (about 55 degrees for this design), the machine works out the amplitude.
Adjusting the WB-1
Two small adjustments sit on the balance cock. The regulator index carries two curb pins that straddle the outer coil of the hairspring. Slide it toward F and the pins move in along the coil, so less of the spring is free to flex: the balance swings faster and the watch gains. Toward S, the reverse. The stud holds the outer end of the spring. Turning its carrier turns the whole hairspring, and with it the place where the balance comes to rest. When the impulse jewel rests exactly on the line to the fork, the tic and toc are even. Move it off that line and the beat error grows. Both sliders drive the timegrapher above.
The balance is set swinging every few seconds and allowed to die away, so you can see where it comes to rest against the dark line to the fork.
On the bench: where the oil goes
A movement needs oil, but too much does more harm than too little: it creeps away from where it is needed and drags dirt with it. So a watchmaker puts a tiny drop in a few exact places and nowhere else. The markers show them on the WB-1, with the movement pulled half apart so you can see between the layers.
- Thin oil in the jewels of the going train, the pallet fork and the balance. The faster a pivot turns, the thinner the oil.
- Escapement oil on the impulse faces of the pallet stones, then spread by letting a few teeth of the escape wheel run through.
- Heavier oil on the barrel arbor, which turns slowly under the full pull of the spring.
- Grease on the mainspring, the keyless works, the click and the winding wheels: slow, heavily loaded, sliding parts.
The balance jewels are worth a second look. The pivot of the balance staff is about as thin as a hair, and the oil there is held in place by the shape of the jewel and its cap stone, a drop small enough that it fills the gap between them and goes no further.
On the bench: taking it apart
A movement comes apart in a fixed order, and the order exists to protect the parts that break most easily. Step through it on the WB-1:
On the bench: when it goes wrong
A movement that comes in rarely says what is wrong with it. It shows a symptom, and the symptom points to a short list of suspects. Pick a symptom: the parts to look at first stay in colour, the rest turn to glass.
Coming next in this series: cleaning, the dial side and the shock protection.